The XP16HPE Features
- 4 Stroke engine.
- Full EPA Approval.
- Start System: Recoil / Electric.
- Ignition System: Transistorized Magneto.
- Air Cleaner: Dual, Semi-dry, Oil Bath, Cyclone.
- Includes Power Panel
- Max Output: 16.0 HP / 3600 RPM.
- Max Torque: 28.5 Nm / 21.0 ft/lb.
- Displacement: 419ml, Bore: 90, Stroke: 66.
- Shaft Size: 1" Dia, 2-3/4" Long, 1/4" Keyway, shaft end drilled & tapped w/ 3/8" 24 UNF.
- Dimensions: 20.47" L, 18.5" W, 22.0" H.
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
How to wire a XP16HPE:
There are 5 wires coming from the key switch.
Connects to a brown wire on the left side of the motor (starter motor towards you) coming from near the recoil assembly.
Connects to the "hot" post on the solenoid. The same post the positive batterly cable connects to.
Connects to the spade connection on the solenoid. Between and above the posts.
If there is a metal box on the engine block near the starter with two wires coming off of it, one of them connected to the low oil sensor coming out of the engine.
• Connect the free male wire to the female from the switch.
If there is not a wire connect to the low oil sensor wire and there is no small metal box near the starter on the engine block.
• Connect the male wire from the low oil sensor to the female from the switch.
Connect the male wire from the switch to the female wire coming from under the fuel tank. It starts at the ignition coil and comes under the tank. It is often hidden behind the starter motor.
** This Engine Can Not Be Shipped to California **
- Customer Reviews
Average! Customer Rating:(10 Reviews)
December 10th, 2014
DuroMax 16 Hp
Comment:Good engine for the money. Installed on a 30 year old wood splitter and it works well
December 4th, 2014
Comment:I purchased one of these to replace the FE290 Kawasiki in my 1996 Club Car two years ago. This engine bolted in to the existing engine mount with no modifiction and has been trouble free since the install, always starts right off in cold weather and has great torque. I would recomend to anyone as a replacement engine for the Club Car engine.
November 19th, 2014
Comment:bolted right up on my portable trencher within 30 mins. it was running. Only have a couple of hours of run time so far but motor has plenty of power to run pump , and seems much quieter then previous motor
November 14th, 2014
Comment:For the money the performance is great. It was easy to adapt to the project and performed well first time out.
October 30th, 2014
Comment:Very nice engine! Well made can't believe quality for price. Maxtools shipping time is awesome had engine in just a couple of days and very well packaged.
July 10th, 2014
Longtail outboard engine
Comment:I use my Duromax on mud-skipper a longtail kit, pushing a 26' long Chinese style raft. It does about 12mph. I had a problem with the ignition switch my fault I think, but they replaced it free of charge. Great engine for this big boat.
July 2nd, 2014
DuroMax 16 Hp., 1'' Shaft, Recoil/Electric Start Engine
Comment:Used this engine to replace an 18HP engine that was on a large wood splintter that had worn out after 30 years of use. I was impressed with how well this engine handles the load. It looks like a Honda engine. How don't know how you could do any better for the price. Max Tools did a super job shipping it out.
November 22nd, 2013
Comment:This engine appears to be well-made, sturdy. Just got it installed and running, so not much experience with durability, but the finish and construction appears to be much better than typical Chinese products (could it be the same mfg. equipment used by Honda?). Hope the inside is as well-made as the outside. If so, I will be very satisfied.
July 20th, 2013
great for what I needed
Comment:I upgraded an old Sears Craftman shredder that is about 25 years old. The motor was shot and I couldn't find another motor with a 1 inch shaft to fit. It was a 5 hp. The one from you is 16 hp but much quieter and starts easier. I had to modify a few things because it was made 25 years ago and thing change. I'm very happy to have found you. I order from you again and tell others. Thank You
April 2nd, 2011
Good buy for clone engine
Comment:I got this for a go kart. It's a LOT bigger than the one that came out of it so I had to work with it some. Take the gas tank off and mount it on the frame. Things like that. Put it all together and it fired right up and has been running flawlessly for the past weeks.